pymelcloud

This is a package for interacting with MELCloud and Mitsubishi Electric devices. It's still a little rough around the edges and the documentation is non-existent.

The goals for this package are:

• To control and automate devices, not to configure them.
• Handle device capabilities behind the scenes.
• Make the different device types behave in predictable way.

Notes on usage

There are built-in rate limits and debouncing for most of the methods with the exception of the Device update method.

• Initialize devices for each account only once during application runtime.
• Make sure the update calls for each Device are rate limited. A 60 second update interval is a good starting point. Going much faster will exceed the expected load for MELCloud and can potentially cause availability issues.
• Make absolutely sure the update calls are rate limited.

Supported devices

• Air-to-air heat pumps (DeviceType=0)
• Air-to-water heat pumps (DeviceType=1)
• Energy Recovery Ventilators (DeviceType=3)

Read

Reads access only locally cached state. Call device.update() to fetch the latest state.

Available properties:

• name
• mac
• serial
• units - model info of related units.
• temp_unit
• last_seen
• power
• daily_energy_consumed
• wifi_signal

Other properties are available through _ prefixed state objects if one has the time to go through the source.

Air-to-air heat pump properties

• room_temperature
• target_temperature
• target_temperature_step
• target_temperature_min
• target_temperature_max
• operation_mode
• available operation_modes
• fan_speed
• available fan_speeds
• vane_horizontal
• available vane_horizontal_positions
• vane_vertical
• available vane_vertical_positions
• total_energy_consumed in kWh. See notes below.

Air-to-water heat pump properties

• tank_temperature
• target_tank_temperature
• tank_temperature_min
• tank_temperature_max
• outside_temperature
• zones
  • name
  • status
  • room_temperature
  • target_temperature
• status
• operation_mode
• available operation_modes

Energy recovery ventilator properties

• room_temperature
• outdoor_temperature
• available fan_speeds
• fan_speed
• actual_supply_fan_speed
• actual_exhaust_fan_speed
• available ventilation_modes
• ventilation_mode
• actual_ventilation_mode
• total_energy_consumed
• wifi_signal
• presets
• error_code
• core_maintenance_required
• filter_maintenance_required
• night_purge_mode
• room_co2_level

Energy consumption

The energy consumption reading is a little strange. The API returns a value of 1.8e6 for my unit. Judging by the scale the unit is either kJ or Wh. However, neither of them quite fits.

• Total reading in kJ matches better what I would expect based on the energy reports in MELCloud.
• In Wh the reading is 3-5 times greater than what I would expect, but the reading is increasing at a rate that seems to match energy reports in MELCloud.

Here are couple of readings with monthly reported usage as reference:

• 2020-01-04T23:42:00+02:00 - 1820400, 28.5 kWh
• 2020-01-05T09:44:00+02:00 - 1821300, 29.4 kWh
• 2020-01-05T10:49:00+02:00 - 1821500, 29.6 kWh

I'd say it's pretty clear that it is Wh and the total reading is not reflective of unit lifetime energy consumption. total_energy_consumed converts Wh to kWh.

Write

Writes are applied after a debounce and update the local state once completed. The physical device does not register the changes immediately due to the 60 second polling interval.

Writable properties are:

• power

Air-to-air heat pump write

• target_temperature
• operation_mode
• fan_speed
• vane_horizontal
• vane_vertical

There's weird behavior associated with the horizontal vane swing. Toggling it on will also toggle vertical swing on and the horizontal swing has to be disabled before vertical vanes can be adjusted to any other position. This behavior can be replicated using the MELCloud user inteface.

Air-to-water heat pump write

• target_tank_temperature
• operation_mode
• zone_1_target_temperature
• zone_2_target_tempeature

Zone target temperatures can also be set via the Zone object returned by zones property on AtwDevice.

Energy recovery ventilator write

• ventilation_mode
• fan_speed

Example usage

import aiohttp
import asyncio
import pymelcloud


async def main():

    async with aiohttp.ClientSession() as session:
        # call the login method with the session
        token = await pymelcloud.login("[email protected]", "mysecretpassword", session=session)

        # lookup the device
        devices = await pymelcloud.get_devices(token, session=session)
        device = devices[pymelcloud.DEVICE_TYPE_ATW][0]

        # perform logic on the device
        await device.update()

        print(device.name)
        await session.close()

loop = asyncio.get_event_loop()
loop.run_until_complete(main())