Hi!
This an IEEE 802.11 a/g/p transceiver for GNU Radio that is fitted for operation with Ettus N210s and B210s. Interoperability was tested with many off-the-shelf WiFi cards and IEEE 802.11p prototypes. The code can also be used in simulations.
Like GNU Radio, this module uses maint branches for development. These branches are supposed to be used with the corresponding GNU Radio branches. This means: the maint-3.7 branch is compatible with GNU Radio 3.7, maint-3.8 is compatible with GNU Radio 3.8, etc.
There are several ways to install GNU Radio. You can use
I have some non project specific GNU Radio blocks in my gr-foo repo that are needed. For example the Wireshark connector. You can find these blocks at https://github.com/bastibl/gr-foo. They are installed with the typical command sequence:
git clone https://github.com/bastibl/gr-foo
cd gr-foo
mkdir build
cd build
cmake ..
make
sudo make install
sudo ldconfig
To actually install the blocks do
git clone https://github.com/bastibl/gr-ieee802-11
cd gr-ieee802-11
mkdir build
cd build
cmake ..
make
sudo make install
sudo ldconfig
Since the transmitter is using the Tagged Stream blocks it has to store a complete frame in the buffer before processing it. The default maximum shared memory might not be enough on most Linux systems. It can be increased with
sudo sysctl -w kernel.shmmax=2147483648
The physical layer is encapsulated in a hierarchical block to allow for a
clearer transceiver structure in GNU Radio Companion. This hierarchical block is
not included in the installation process. You have to open
/examples/wifi_phy_hier.grc with GNU Radio Companion and build it. This
will install the block in ~/.grc_gnuradio/.
Sometime the connections between the message ports (the gray ones in GNU Radio Companion) break. Therefore, please open the flow graphs and assert that everything is connected. It should be pretty obvious how the blocks are supposed to be wired. Actually this should not happen anymore, so if your ports are still unconnected please drop me a mail.
If you want to run the receive demo (the one that plots the subcarrier constellations), please assert that you have python-opengl installed. The nongl version of the plot does not work for me.
volk_profile is part of GNU Radio. It benchmarks different SIMD implementations on your PC and creates a configuration file that stores the fastest version of every function. This can speed up the computation considerably and is required in order to deal with the high rate of incoming samples.
If you have a WBX, SBX, or CBX daughterboard you should calibrate it in order to minimize IQ imbalance and TX DC offsets. See the application notes.
As a first step I recommend to test the wifi_loopback.grc flow graph. This
flow graph does not need any hardware and allows you to ensure that the software
part is installed correctly. So open the flow graph and run it. If everything
works as intended you should see some decoded packets on the console.
If GRC complains that it can't find some blocks (other than performance counters and hierarchical blocks) like
>>> Error: Block key "ieee802_11_ofdm_mac" not found in Platform - grc(GNU Radio Companion)
>>> Error: Block key "foo_packet_pad" not found in Platform - grc(GNU Radio Companion)
Most likely you used a different CMAKE_INSTALL_PREFIX for the module than
for GNU Radio. Therefore, the blocks of the module ended up in a different
directory and GRC can't find them. You have to tell GRC where these blocks are
by creating/adding to your ~/.gnuradio/config.conf something like
[grc]
global_blocks_path = /opt/local/share/gnuradio/grc/blocks
local_blocks_path = /Users/basti/usr/share/gnuradio/grc/blocks
But with the directories that match your installation.
The loopback flow graph should give you an idea of how simulations can be conducted. To ease use, most blocks have debugging and logging capabilities that can generate traces of the simulation. You can read about the logging feature and how to use it on the GNU Radio Wiki.
As first over the air test I recommend to try wifi_rx.grc and
wifi_tx.grc. Just open the flow graphs in GNU Radio companion and execute
them. If it does not work out of the box, try to play around with the gain. If
everything works as intended you should see similar output as in the
wifi_loopback.grc example.
- The transceiver is currently connected to a TAP device, i.e. is a virtual Ethernet interface. Therefore, we have no WiFi signaling like association requests and hence, the transceiver can not "join" an ad hoc network. You have to make some small changes to the kernel in order to convince you WiFi card to send to this hosts nevertheless.
- The transceiver can not respond to ACKs in time. This is kind of an architectural limitation of USRP + GNU Radio since Ethernet and computations on a normal CPU introduce some latency. You can set the number of ACK retries to zero and handle retransmits on higher layers (-> TCP).
- RTS/CTS is not working for the same reason. You can however just disable this mechanism.
- Currently, there is no CSMA/CA mechanism, but this can be implemented on the FPGA.
-
Please check compile and installation logs. They might contain interesting information.
-
Did you calibrate your daughterboard?
-
Did you run volk_profile?
-
Did you try different gain settings?
-
Did you close the case of the devices?
-
Did you try real-time priority?
-
Did you compile GNU Radio and gr-ieee802-11 in release mode?
-
If you see warnings that
blocks_ctrlport_monitor_performanceis missing that means that you installed GNU Radio without control port or performance counters. These blocks allow you to monitor the performance of the transceiver while it is running, but are not required. You can just delete them from the flow graph. -
The message
You must now use ifconfig to set its IP address. E.g., $ sudo ifconfig tap0 192.168.200.1
is normal and is output by the TUN/Tap Block during startup. The configuration
of the TUN/TAP interface is handled by the scripts in the apps folder.
- Did you try to tune the RF frequency out of the band of interest (i.e. used the LO offset menu of the flow graphs)?
- If 'D's appear, it might be related to your Ethernet card. Assert that you made the sysconf changes recommended by Ettus. Did you try to connect you PC directly to the USRP without a switch in between?
For further information please checkout our project page https://www.wime-project.net