Timeout Error

[CalFamily]

I'm new to CNC so be gentle!!

I've got my machine connected and can run a project. There have been a few times I've needed to stop the project before the end for one reason or another. When I hit the STOP button, the progress pauses. When I hit it again to cancel, I get the message "[Error] Timeout waiting for GRBL to Idle during cancel, cancel incomplete." In order to abort a project I have to pause, then disconnect the machine and reconnect. That doesn't work well when the reason for a pause is a bit change within the project because when I reconnect the work coordinate zero isn't the same.

Any suggestions?

[breiler]

What type of controller are you using? What firmware are you using (for instance GRBL 1.1f)? What version of UGS have you installed?

[CalFamily]

I just use UGS onboard controls no external or add on controllers. The firmware I have selected is GRBL and it’s the only one in the drop down menu. If there is anything else that I should be using I don’t k ow about it (like I said, I’m super new to this). I think I have the most up to date version. When I check for updates it says I’m up to date. Under the about it says “Product Version UGS Platform 20300207”

…

On Fri, Aug 23, 2024 at 11:16 AM Joacim Breiler ***@***.***> wrote: What type of controller are you using? What firmware are you using (for instance GRBL 1.1f)? What version of UGS have you installed? — Reply to this email directly, view it on GitHub <#2592 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BKXR5RXOQX2SCAYA6JHDWODZS5U7JAVCNFSM6AAAAABNAPLTFWVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTANBTGMYDMMY> . You are receiving this because you authored the thread.Message ID: <winder/Universal-G-Code-Sender/repo-discussions/2592/comments/10433063@ github.com>

[breiler]

I just use UGS onboard controls no external or add on controllers. The
firmware I have selected is GRBL and it’s the only one in the drop down
menu.

I want to know the version of GRBL you have installed

Under the about it says “Product Version UGS Platform 20300207”

The numbers should form a date as YYYYMMDD, can you take a screenshot and upload it here.

[CalFamily]

I’m not sure if this is what you’re looking for. When I connect to the machine this is what comes up. If this isn’t what you need where do I find the version of GRBL?

…

On Thu, Aug 29, 2024 at 12:58 PM Joacim Breiler ***@***.***> wrote: I just use UGS onboard controls no external or add on controllers. The firmware I have selected is GRBL and it’s the only one in the drop down menu. I want to know the version of GRBL you have installed Under the about it says “Product Version UGS Platform 20300207” The numbers should form a date as YYYYMMDD, can you take a screenshot and upload it here. — Reply to this email directly, view it on GitHub <#2592 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BKXR5RWHREVT7JYIZWWCFLTZT5VNZAVCNFSM6AAAAABNAPLTFWVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTANBZGA4DCMQ> . You are receiving this because you authored the thread.Message ID: <winder/Universal-G-Code-Sender/repo-discussions/2592/comments/10490812@ github.com>

[breiler]

If you tried to attach a image via email that doesn't work. You need to attach it on GitHub.

[CalFamily]

hopefully that works

[breiler]

Ok that is the later version of GRBL so that should be ok.

What version of UGS, take a screen shot of the entire application.

[CalFamily]

[breiler]

That is the UGS version supplied from MillRight, and it looks ancient.

You should try to upgrade to the latest version here: https://universalgcodesender.com/download/

[CalFamily]

Hello! My mother board on my computer had an unfortunate accident and it’s taken a minute to get a new computer. I’ve downloaded the new version of UGS. Now the problem I’m running into is that when I import my gcode file from carbide create, nothing shows up in UGS. It has no toolpaths for the design I created so now I can’t cut anything at all. Any suggestions for that?

…

On Sun, Sep 1, 2024 at 12:05 PM Joacim Breiler ***@***.***> wrote: That is the UGS version supplied from MillRight, and it looks ancient. You should try to upgrade to the latest version here: https://universalgcodesender.com/download/ — Reply to this email directly, view it on GitHub <#2592 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BKXR5RU577J2S2NCOAIHF4DZUNJN7AVCNFSM6AAAAABNAPLTFWVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTANJRGM4DGNA> . You are receiving this because you authored the thread.Message ID: <winder/Universal-G-Code-Sender/repo-discussions/2592/comments/10513834@ github.com>