-
Notifications
You must be signed in to change notification settings - Fork 49
/
my_machine.h
156 lines (142 loc) · 8.41 KB
/
my_machine.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
/*
my_machine.h - configuration for Raspberry RP2040 ARM processors
Part of grblHAL
Copyright (c) 2021-2024 Terje Io
grblHAL is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
grblHAL is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with grblHAL. If not, see <http://www.gnu.org/licenses/>.
*/
// NOTE: Only one board may be enabled!
// If none is enabled pin mappings from generic_map.h will be used.
//#define BOARD_PICO_CNC
//#define BOARD_PICOBOB
//#define BOARD_PICOBOB_G540
//#define BOARD_PICOBOB_DLX
//#define BOARD_PICOBOB_DLX_G540
//#define BOARD_BTT_SKR_PICO_10 // incomplete and untested!
//#define BOARD_CNC_BOOSTERPACK
//#define BOARD_CITOH_CX6000 // C.ITOH CX-6000 HPGL plotter
//#define BOARD_GENERIC_4AXIS
//#define BOARD_MY_MACHINE // Add my_machine_map.h before enabling this!
// Configuration
// Uncomment to enable.
#ifndef USB_SERIAL_CDC
#define USB_SERIAL_CDC 1 // Serial communication via native USB.
#endif
//#define BLUETOOTH_ENABLE 2 // Set to 2 for HC-05 module, enable in CMakeLists.txt if for Pico W Bluetooth.
// Spindle selection:
// Up to four specific spindle drivers can be instantiated at a time
// depending on N_SPINDLE and N_SYS_SPINDLE definitions in grbl/config.h.
// If none are specified the default PWM spindle is instantiated.
// Spindle definitions can be found in grbl/spindle_control.h.
// More here https://github.com/grblHAL/Plugins_spindle
//#define SPINDLE0_ENABLE SPINDLE_HUANYANG1
//#define SPINDLE1_ENABLE SPINDLE_PWM0
//#define SPINDLE2_ENABLE SPINDLE_NONE
//#define SPINDLE2_ENABLE SPINDLE_NONE
//#define SPINDLE_OFFSET 1 // Set to 1 to add offset move when switching between laser and spindle
// **********************
//#define MODBUS_ENABLE 1 // Set to 1 for auto direction, 2 for direction signal on auxiliary output pin.
//#define WIFI_ENABLE 0 // Do NOT enable here, enable in CMakeLists.txt!
//#define WIFI_SOFTAP 1 // Use Soft AP mode for WiFi. NOTE: WIP - not yet complete!
//#define ETHERNET_ENABLE 0 // Do NOT enable here, enable in CMakeLists.txt!
//#define _WIZCHIP_ 5500 // Selects WIZnet ethernet breakout connected via SPI.
// Uncomment to enable W5500 chip, default is W5100S. Requires ethernet enabled in CMakeLists.txt.
//#define WEBUI_ENABLE 1 // Enable ESP3D-WEBUI plugin along with networking and SD card plugins. Requires WiFi enabled.
//#define WEBUI_AUTH_ENABLE 1 // Enable ESP3D-WEBUI authentication.
//#define WEBUI_INFLASH 1 // Store WebUI files in flash instead of on SD card.
//#define SDCARD_ENABLE 2 // Run gcode programs from SD card. Set to 2 to enable YModem upload.
//#define MPG_ENABLE 1 // Enable MPG interface. Requires a serial stream and means to switch between normal and MPG mode.
// 1: Mode switching is by handshake pin.
// 2: Mode switching is by the CMD_MPG_MODE_TOGGLE (0x8B) command character.
//#define KEYPAD_ENABLE 1 // 1: uses a I2C keypad for input.
// 2: uses a serial stream for input. If MPG_ENABLE is set > 0 the serial stream is shared with the MPG.
//#define DISPLAY_ENABLE 1 // Set to 1 for I2C display protocol, 2 for I2C LED protocol.
//#define ODOMETER_ENABLE 1 // Odometer plugin.
//#define LASER_COOLANT_ENABLE 1 // Laser coolant plugin. To be completed.
//#define LB_CLUSTERS_ENABLE 1 // LaserBurn cluster support.
//#define FANS_ENABLE 1 // Enable fan control via M106/M107. Activates fan plugin.
//#define EMBROIDERY_ENABLE 1 // Embroidery plugin. To be completed.
//#define TRINAMIC_ENABLE 1 // Trinamic TMC2130 stepper driver support. NOTE: work in progress.
//#define TRINAMIC_I2C 1 // Trinamic I2C - SPI bridge interface.
//#define TRINAMIC_DEV 1 // Development mode, adds a few M-codes to aid debugging. Do not enable in production code.
//#define EEPROM_ENABLE 16 // I2C EEPROM/FRAM support. Set to 16 for 2K, 32 for 4K, 64 for 8K, 128 for 16K and 256 for 16K capacity.
//#define EEPROM_IS_FRAM 1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
//#define STEP_INJECT_ENABLE 1
//#define MCP3221_ENABLE 0x4D // Enable MCP3221 I2C ADC input with address 0x4D (0b01001101).
//#define RGB_LED_ENABLE 2 // Set to 1 to enable strip length settings $536 and $537, set to 2 to also enable M150 LED strip control.
//#define PWM_SERVO_ENABLE 1 // Enable M280 PWM servo support, requires at least one PWM capable auxiliary output.
//#define BLTOUCH_ENABLE 1 // Enable M401/M402 BLTouch support. Requires and claims one auxiliary PWM servo output.
//#define EVENTOUT_ENABLE 1 // Enable binding events (triggers) to control auxiliary outputs.
//#define ESP_AT_ENABLE 1 // Enable support for Telnet communication via UART connected ESP32 running ESP-AT.
//#define FEED_OVERRIDE_ENABLE 1 // Enable M200 feed override control.
//#define HOMING_PULLOFF_ENABLE 1 // Enable per axis homing pulloff distance settings.
// Optional control signals:
// These will be assigned to aux input pins. Use the $pins command to check which pins are assigned.
// NOTE: If not enough pins are available assignment will silently fail.
//#define PROBE_ENABLE 0 // Default enabled, remove comment to disable probe input.
//#define SAFETY_DOOR_ENABLE 1
//#define MOTOR_FAULT_ENABLE 1
//#define MOTOR_WARNING_ENABLE 1
//#define PROBE_DISCONNECT_ENABLE 1
//#define STOP_DISABLE_ENABLE 1
//#define BLOCK_DELETE_ENABLE 1
//#define SINGLE_BLOCK_ENABLE 1
//#define LIMITS_OVERRIDE_ENABLE 1
// If the selected board map supports more than three motors ganging and/or auto-squaring
// of axes can be enabled here.
//#define X_GANGED 1
//#define X_AUTO_SQUARE 1
//#define Y_GANGED 1
//#define Y_AUTO_SQUARE 1
//#define Z_GANGED 1
//#define Z_AUTO_SQUARE 1
// For ganged axes the limit switch input (if available) can be configured to act as a max travel limit switch.
// NOTE: If board map already has max limit inputs defined this configuration will be ignored.
//#define X_GANGED_LIM_MAX 1
//#define Y_GANGED_LIM_MAX 1
//#define Z_GANGED_LIM_MAX 1
//
//#define _WIZCHIP_ 5500
#if WIFI_ENABLE || ETHERNET_ENABLE || WEBUI_ENABLE
#define TELNET_ENABLE 1 // Telnet daemon - requires WiFi streaming enabled.
#define WEBSOCKET_ENABLE 1 // Websocket daemon - requires WiFi streaming enabled.
//#define MDNS_ENABLE 0 // mDNS daemon. Do NOT enable here, enable in CMakeLists.txt!
//#define SSDP_ENABLE 1 // SSDP daemon - requires HTTP enabled.
#if SDCARD_ENABLE || WEBUI_ENABLE
#define FTP_ENABLE 1 // Ftp daemon - requires SD card enabled.
//#define HTTP_ENABLE 1 // http daemon - requires SD card enabled.
//#define WEBDAV_ENABLE 1 // webdav protocol - requires http daemon and SD card enabled.
#endif
// The following symbols have the default values as shown, uncomment and change as needed.
//#define NETWORK_STA_HOSTNAME "grblHAL"
//#define NETWORK_STA_IPMODE 1 // 0 = static, 1 = DHCP, 2 = AutoIP
//#define NETWORK_STA_IP "192.168.5.1"
//#define NETWORK_STA_GATEWAY "192.168.5.1"
//#define NETWORK_STA_MASK "255.255.255.0"
#if WIFI_SOFTAP > 0
//#define NETWORK_AP_SSID "grblHAL_AP"
//#define NETWORK_AP_PASSWORD "grblHALap"
//#define NETWORK_AP_HOSTNAME "grblHAL_AP"
//#define NETWORK_AP_IPMODE 0 // Do not change!
//#define NETWORK_AP_IP "192.168.4.1" // Do not change!
//#define NETWORK_AP_GATEWAY "192.168.4.1" // Do not change!
//#define NETWORK_AP_MASK "255.255.255.0"
#endif
//#define NETWORK_FTP_PORT 21
//#define NETWORK_TELNET_PORT 23
//#define NETWORK_HTTP_PORT 80
#if HTTP_ENABLE
//#define NETWORK_WEBSOCKET_PORT 81
#else
//#define NETWORK_WEBSOCKET_PORT 80
#endif
#endif // WIFI_ENABLE
/**/